Product Questions for Scrapbook.com - Clear Double Sided Adhesive Roll - 2 Inch x 81 Feet - 1 Roll

Yes you can. I haven't used this roll of tape that way yet (haven't had time) but I use my rolled and flat adhesive sheets that way frequently. Some dies will cut all the way through, some will leave the backing intact, and you are able to adjust the pressure on electric cutters for a "kiss cut", like when using vinyl, so that the top material is cut but the backing is left intact. By: Wendy Loveland (07-Aug-18) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

Yes, you totally can! You will need to adhere your paper to the cutting mat with a little bit of removable tape since the backing on the adhesive is non-stick. That means it won't stick to your cutting mat either. A little washi tape on all 4 sides of your paper works great. By: Scrapbook.com (11-Mar-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

We use it on both of those machines, after adhering it to the paper you wish to cut. The only thing I will recommend is when you place your paper on the cutting mat, you will want to add a little washi tape to the sides of your paper to keep it from sliding while cutting. The backing paper has a non-stick surface, that means it won't stick to the cutting mat either. Removable tape works great to tack down the edges of the paper to the cutting mat and keep the paper from moving on the mat while cutting. Hope that helps. By: Scrapbook.com (11-Mar-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

Yes, but you would have to adhere it your Cardstock first. When you are rolling it off of the roll, only one side has a backing attached. By: Lopezdn (01-Mar-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

Yes. I only used it several times and so far it lied flat for me. By: ngardley (15-May-18) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

Yes it does and i love this stuff! Just be aware that when you pull it off the roll one side is sticky and ready to be applied. By: idtegacay (11-Mar-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

It is very thin.I wouldn't call it crystal clear but yes you can see through it really well. I love it. By: FlowerPower23 (29-Aug-20) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

After looking up what "Hot fixed Swarovski" were, I would say no... This adhesive is great for paper products, however is not super thick. I don't think it has the "rubber" like texture you are looking for. Perhaps an epoxy might work better. By: jkathybrazil (25-Aug-20) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

Yes, the Scrapbook.com Clear Double Sided Adhesive Roll is acid-free, archival, and heat resistant! By: PaperMischief (15-Apr-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

I personally use both. I save the larger sheets for bigger die cuts and use the rolls for the smaller items like small stamps, letters and words. You will save money over time using the rolls but the sheets are super convenient. It is very much a personal preference. :) Great question. By: PaperMischief (08-Apr-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

It could possibly work in this capacity. However, there might be stickiness on the open parts of the mesh trim. You could try using some sort of powder to take away the stickiness though. Hope this helps! By: sbc-julie (19-Apr-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

I'm sorry, but I can't quite envision your situation from your question. You say you can't remove the cutouts from the dies? Right? I've seen suggestions of putting a layer of wax paper between the cardstock and the die. And you also say that you can't peel the adhesive from the shapes that have been cut out. That can be tricky. I'm envisioning that you have finally removed the cutout from the die and are now trying to adhere it to your project. Do you have any kind of weeding tool? I have a small hooked tool that I use and Spellbinders has something that I think is called a Tool-in-one with a little brush on one end to clean some of the debris out of the dies and a nice point on the other end. It can be tricky to get find a spot to start the peel, but then it should come off well. I don't know if this helps at all, but I hope you are able to make something work for you. That big roll is an investment! Good luck. By: cricutkate (08-Dec-18) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

Thanks, cricutkate! Great advice. If those suggestions didn't work, you could also use the Sizzix Tweezers https://www.scrapbook.com/store/sz-661670.html to poke through the release holes in your dies. Most dies typically have tiny holes in them for allowing you to pop out your paper if it gets stuck in the die. I also use the same tweezers to release the backing paper for the adhesive. I have also cut dryer sheets with my dies to get the paper to release easier. It gently coats the die with an anti-static layer. I hope they gives you a few options to try. By: Scrapbook.com (11-Mar-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

Unfortunately, I would not recommend using this to hang a panel on the wall. You might want to try some sort of liquid glue. Just a suggestion.
I hope this helps:) By: Amber Boren (04-Oct-18) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

It is really strong but it would probably depend on how large the piece of metal is. The weight would be a big factor for whether it would hold or not. We have used it on both metal and wood, it does work on both but we haven't tried anything really heavy. Good luck! By: Scrapbook.com (11-Mar-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

I love it, it is just like double sided tape only it's big enough for your die's that need cut. love it By: loishuffman (03-Aug-18) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

It is solid, and great to use with elizabeth dies and extra fine glitter By: beci55 (02-Aug-18) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

I haven't had it long enough to know if it will dry out or not. but I use the 1/2 tape and it don't dry out and the fronts don't fall off my cards. I hope this helps you. most of the tapes are the same, only different in size. good luck and have fun with you 6'' tape. By: loishuffman (03-Aug-18) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

It's a dry adhesive, like tape. So no, it will not dry out. By: mariyagiggles (30-May-18) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

YES!!! The adhesive works great with embossing powder. As long as you don't leave the heat tool too long in one place, it works beautifully. Keep your heat tool moving and you won't have any problem. It works with foil too, no heat needed. Deco Foil from Therm O Web works great with the adhesive. Hope that helps. By: Scrapbook.com (11-Mar-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

I'm sorry I can't answer your question, I've always heat embossed before using the tape. I'd try heating a small piece one some paper and see how it handles the heat. By: sher.g (08-Jan-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

Hello and thank you for your question! Yes, this tape will hold glitter and gold flakes! By: Scrapbook.com (07-Jan-20) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!

It is very similar to the Scor-Tape. It is SUPER sticky and does an AMAZING job for book binding. It will adhere really well the second it touches your paper so be sure to place it carefully the first time, you won't be able to remove it easily. That makes it the perfect solution for binding scrapbooks. By: Scrapbook.com (29-Apr-19) Helpful Answer?  Yes  |  No Thank you! Report Inappropriate This Answer has been reported. Thank you!